| Frequency
|
|
| Frequency Range |
100 KHz - 1.3 GHz LOWBAND, 1.2-2.5 GHz HIGHBAND(OPTIONAL) |
| Span |
20 Khz to 2.5 Ghz |
| Center Frequency |
0Hz to 2.5Ghz |
| Marker Error |
+/- 1% Span
+/- 280 x Freq Ref Err
|
| R.B.W. |
300KHz, 100KHz, 15KHz, 3KHz
Option 002:300 Hz
|
| RBW Accuracy |
+/- 10 % |
| RBW Selectivity 60dB / 3dB |
5:1 Typical, 4 Pole Filter |
| Drift |
<50 Hz / Min., 30 Min warmup (without TCXO option) |
| Reference Oscillator |
Freq Ref Error: +/- 500 Hz @ 10 Mhz
Option 007 (TCXO): +/- 10 Hz |
| 1st L.O. Spectral Purity |
-85 dBc/Hz @ 10 KHz Offset, 1Hz B.W. |
| Video Bandwidths |
100Hz, 1 KHz, 10KHz, 100KHz and 300KHz |
| Amplitude
|
|
| Measurment Range |
-130 dBm to +20 dBm |
| Max. Safe Input Power (CW) |
+20 dBm (Internal Attenuator Limit) |
| Display Calibration |
1 THRU 20 dB / div |
| Display & Readout Power Accuracy |
Avg Err. +/-1.0 dB, +/- 2.0 dB Max.
With 20dB Internal Attenuation, PreAmp On, -45dB C.W. Input, 3 KHz RBW, 1 MHz to 2.2GHz
|
| Incremental Resolution |
+/- 0.15 dB Maximum. +/- 0.1 dB Typical |
| Frequency Response Flatness |
+/- 1.4 dB from 1MHz to 2.2GHz
3 to 6 dB roll off @ 1.2 GHz and 2.5GHz |
| Internal Attenuator Range |
20 dB in one step standard
Option 003: 50 dB Attenuator, 10 dB steps |
| Spurious Free Dynamic Range |
75 dB @ 3 KHz RBW |
| Dynamic Range@ 1 dB Compression |
>90 dB @ 300 Hz RBW |
| Residual Responses |
< -100 dBm with input terminated, 0 dB attenuation, PreAmp On. |
| 3rd Order Intercept |
0 dBm (Preamp ON)
+15 dBm (Preamp OFF, Option 005)
Option 005: Preamp Relay |
| Time
Related Specs |
|
| 1st LO Settling Time |
< 200 µS typical |
| Sweep Time |
DOS Software:
Min: 50 msec . Max: > 5 min.
486 Based System @ 33 MHz |
| Sweep Trigger Modes |
Internal, avail @ Rear Pannel Jack
TTL, SMB Connector |
| Video Digitizing Rate/ Resolution |
> 50Ksps, 10 Bits |
| External
Input Characteristics |
|
| RF Input |
50 Ohm, SMA, female ( TYPE N OPTIONAL) |
| RF Input VSWR |
< 1.5:1 , 0 dB attenuation
< 1.3:1 with 10dB or more attenuation |
| Ext. Reference Input Frequency |
10 MHz Sinewave/TTL (OPTIONAL) |
| RF
In/ Out Characteristics |
|
| 1st L.O. Output Level |
-5 dBm(contact factory on this option) |
| Video Output |
0 to +4 Volt Full Scale(contact factory on this option) |
| I.F. Output/Input |
2nd IF@ 250 MHz, 3rd IF @10.7 MHz
Contact factory on these optional OUT/IN connections |
| Other
Specifications |
|
| Power Requirement |
1 amp @ 12 volts(DC Input)
|
| Weight |
< 3 lbs (no internal battery)
< 6 lbs (with internal battery) |
| Operation time on internal battery |
Approx. 1 hr, 6 hrs recharge |
| Case Size(WxHxD, Inches) |
5.75 x 2.6 x 9.4 |
| System Requirements |
IBM PC or compatible with VGA monitor, 1.4 MbB floppy drive, One Parrallel Port.
DOS Software: 2 MB Ram ,and DOS 4.0 or higher. A 386 processor or better is recommended.
Windows Software: Windows 95/98 supported |
